MODEL | PSP-600-15 | |
OUTPUT | DC VOLTAGE | 15V |
CURRENT RANGE | 0 ~ 40A | |
RATED CURRENT | 40A | |
RATED POWER | 600W | |
RIPPLE & NOISE (max.) Note.2 | 240mVp-p | |
VOLTAGE ADJ. RANGE | 13.5 ~ 18V | |
VOLTAGE TOLERANCENOTE.3 | 1.0% | |
LINE REGULATION | 0.5% | |
LOAD REGULATION | 0.5% | |
SETUP, RISE TIME | 1500ms, 50ms at full load | |
HOLD UP TIME (Typ.) | 20ms at full load | |
INPUT | VOLTAGE RANGE | 88 ~ 264VAC 124 ~ 370VDC |
FREQUENCY RANGE | 47 ~ 63Hz | |
POWER FACTOR (Typ.)? | 0.95/230VAC 0.99/115VAC at full load | |
EFFICIENCY (Typ.) | 85% | |
AC CURRENT (Typ.) | 6.8A/115VAC 3.4A/230VAC | |
INRUSH CURRENT (Typ.) | 20A/115VAC 40A/230VAC | |
LEAKAGE CURRENT | <1.3mA/240VAC | |
PROTECTION | OVER LOAD | 105 ~ 135% rated output power |
Protection type : Constant current limiting, recovers automatically after fault condition is removed | ||
OVER VOLTAGE | 18 ~ 21V | |
Protection type : Shut down o/p voltage,fe-power on to tecovery | ||
OVER TEMPERATURE | +5V: 95 (TSW1) detect on heatsink of power transistor; 95 (TSW51) detect on heatsink of power diode | |
+12V ~ +48V: 85 (TSW1) detect on heatsink of power transistor; 80 (TSW51) detect on heatsink of power diode | ||
Protection type : Shut down o/p voltage,fe-power on to tecovery | ||
REMOTE CONTROL | RC+/RC-: Short = power on ; Open = power off | |
POK SIGNAL | PSU turn on: 3.3V ~ 5.6V PSU turn off: 0V ~ 1V | |
ENVIRONMENT | WORKING TEMP. | -20 ~ +60°C (Refer to output load derating curve) |
WORKING HUMIDITY | 20 ~ 90% RH non-condensing | |
STORAGE TEMP., HUMIDITY | -40 ~ +85°C , 10 ~ 95% RH | |
TEMP. COEFFICIENT | 0.03%/°C (0 ~ 50°C ) | |
VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, period for? 60min. each along X, Y, Z axes | |
SAFETY &EMC(Note 4) | SAFETY STANDARDS | UL60950-1, TUV EN60950-1 approved |
WITHSTAND VOLTAGE | I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC | |
ISOLATION RESISTANCE | I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC / 25 / 70% RH | |
EMI CONDUCTION & RADIATION | Compliance to EN55022 (CISPR22) Class B | |
HARMONIC CURRENT | Compliance to EN61000-3-2,-3 | |
EMS IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, light industry level, criteria A | |
OTHERS | MTBF | 116.4K hrs min. MIL-HDBK-217F (25 ) |
DIMENSION | 170*120*93mm (L*W*H) | |
PACKING | 1.9Kg; 8pcs/15.5Kg/1.06CUFT | |
NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°Cof ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meetsEMC directives.5. Derating may be needed under low input voltages. Please check the derating curve for more details. | |
Mechanical Specification & Block Diagram & Derating Curve |