72 Cav. Pet Preform Line with The Cooling Robot, Two Screw ,Cycle 10s, 23000pcs/h, 4560g, 500T.

Demark 72 cavities pet preform line molding system@injection molding machine@) uses a new part cooling and handling system, which features:    1.  Cooling on the inner surface of the preform without using compressed air, unlike most post-mold cooling systems which only cool the outer surface    2.  Optimized cycle utilization — being mounted on the moving platen, the cooling system remains active for up to 85% of the overall cycle.Demark pet preform injection molding systems are available from 280 to 500 tonnes (2800 to 5000 kN) and up to 96 cavities.Demark pet injection systems offer:    1.  Faster cycles(9s)    2.  Reduced energy consumption    3.  Smaller footprint     4.  Improved repeatability     5.  Rapid set-up     1.  Two state plasticizing enables plenty injection quantity;    2.  Take out plate with three working position insures sufficient cooling time and shorter cycle time;    3.  High quality parts and accessories from world famous brands enable higher speed and precision;    4.  Special screw design increases torque while brings down shear force to avoid degradation;    5.  Accumulator from world reputable manufacture increases performance while brings down power consumption; Reflex PlatensReflex platens distribute clamp force evenly across the platen face.Reflex platens:    1.  Allow for 10-30% lower clamp tonnage     2.  Decrease mold wear     3.  Improve part quality  Injection Unitsdemark systems offer both reciprocating screw (RS) and two-stage injection units. RS units offer the performance required for many PET applications while two-stage is appropriate for higher throughput applications. ControlsDMK-based controls manage all functions of our PET production systems, with optional packages to integrate auxiliaries and downstream part handling equipment. Advantages include:    1.  Faster cycle times     2.  Improved shot-to-shot repeatability     3.  Remote connectivity through ServiceNetLink     4.  Control of molding system and auxiliaries from a single interface  Linear BearingsLinear bearings support the moving platen directly on the machine base. This design reduces mold wear by improving platen alignment and perpendicularity, and provides a grease free molding environment. @(injection

Features:

ITEM		UNIT	DMK-PET72A	DMK-PET72B
INJECTION UNIT	Screw L/D Ratio	L/D	25	25
	Screw Diameter	mm	120	140
	Injection Pressure	Kgf/cm2	875	875
	Output(Max)	Pcs/h	23000	23000
	Theory Shot Volume(Max)	cm	3800	5400
	Shot Weight(PS)	g	4560	6500
		ozs	161	230
CLAMPING UNIT	Clamping Force	T	500	500
	Clamping Stroke	mm	680	680
	Max/Min Thickness of Mould	mm	300~820	300~820
	Space Between Tie Bars (WxH)	mm	820~820	820~820
	Ejector Stroke	mm	200	200
	Ejector Force	T	21	21
	NO.of Ejector Pins	PCS	13	13
	Max Pressure of System	Kg/cm2	140	140
MOULD&ROBOT	Cavity(Max)	PCS	72	72
	Neck of Bottle(Max)	mm	42	42
	Length of Preform(Max)	mm	220	220
	Weight of Preform(Max)	g	35	50
	Type of Mould	Needle Valve of No-Cutting PET Preform Molds
	Manipulator	Cavity	72x3	72x3
	Cooling Form	Cavity	216	216
POWER UNIT	Pump Motor Power	KW	25	25
	Robot Power	KW	25	25
	Mould Heater Capacity	KW	68	68
	Heater Input Capacity	KW	87	87
	Total Power	KW	325	325
OTHER	Electric Power Supply(3-phase AC)	V/HZ	380/50	380/50
	Chilling Water	°C	5~15	5~15
		Mpa	0.6	0.6
		L/min	800	900
	Coolling Water	°C	30~55	30~55
		Mpa	0.25	0.25
		L/min	300	300
	Compressed Air	Mpa	0.7~0.9	0.7~0.9
		L/min	1200	1200
	Machine Size (LxWxH)	mm	9765x4547x2350	9765x4547x2350

72 Cav. Pet Preform Line (Two Screw)