Ads by Google
SE11034 Manual Vacuum Pump:
Vacuum System Testing1. Position the vehicle in a flat, level outdoor area. Set the parking brake and chock the tires.2. Attach a 23" Hose (4) to the Vacuum Pump (1).3. Attach the other end of the Hose to the vacuum system. Keep clear of parts that will move or get hot while an assistant starts the engine. Wait until the vacuum reading stabilizes and compare it to the manufacturer’s specification.4. After obtaining a measurement, shut off the engine.5. A low or unstable vacuum reading may mean a vacuum leak, vacuum line blockage, cylinder sealing problems, incorrect valve/ignition timing, or other issues.Note: Vehicle vacuum systems will differ. Consult the vehicle’s service manual for proper testing procedures.6. After testing is complete, disconnect the Vacuum Pump and Hose, remove any plugs or clamps and secure all vacuum lines.
Brake Bleeding1. Attach a 3" Hose (5) to the bottom of the Suction Lid (2a).2. Attach a 23" Hose (4) to the port on the top of the Suction Lid (2a) that does not have the 3" Hose attached, as shown in Figure A. Then, attach the other end of that 23" Hose to the Vacuum Pump (1).3. Make sure the O-ring (11) is completely seated into the groove on the top of the Cup to provide a good seal. Firmly attach the Suction Lid (2a) to the Cup (3).4. Remove the cap from the vehicle’s master cylinder, and make sure the master cylinder is full of brake fluid. If not full, fill the master cylinder to capacity with clean, new brake fluid. (Use only the kind of brake fluid recommended by the vehicle manufacturer.)Note: Determine the proper brake bleeding sequence from your vehicle service manual(i.e., right rear wheel, left rear wheel, right front wheel, left front wheel).5. Connect the 23" Hose (4) to the remaining port on the Suction Lid (2a).6. Insert the Tapered Hose Adapter (6) into the 23" Hose. Connect the other end of the adapter to the Brake Bleed Screw Adapter (9).7. Squeeze the Handle of the Vacuum Pump (1) 10 to 15 times to create a vacuum in the Cup (3). (Note: The Gauge on the Vacuum Pump should read at approximately 10 inHg. Do not exceed 20 inHg. A greater vacuum could damage the vehicle’s brake system.)8. Open the vehicle’s brake caliper bleed screw, and allow brake fluid to flow into the Cup (3) until fluid appears clear and free of bubbles. Then, retighten the bleed screw.
9.Release the vacuum in the Vacuum Pump (1) with the Vacuum Release Valve. Then, disconnect the Brake Bleed Screw Adapter (9) from the vehicle’s brake caliper bleed screwNote: Do not allow the cup to fill completely with brake fluid. When necessary, release the vacuum in the tool and empty its Cup (3) of old brake fluid. To assist in transport, this set includes a Transport Lid (2b) without hose connections. After the brake fluid is disposed of properly, resume bleeding the brakes.10. Remove the cap from the vehicle’s master cylinder, and refill the master cylinder back to its normal capacity with clean, new brake fluid. Then, replace the cap on the master cylinder.11. Proceed to the vehicle’s next brake caliper, and perform the same steps as above.12. When finished using the Vacuum Pump, clean the tool and store it in a clean, dry location out of reach of children.13. WARNING! Before driving the vehicle, carefully check for leaks and test for proper brake operation.
Packing:
About us:
-- Established on Aug. 30th, 1980 with a registered capital of RMB 37, 000,000.00;
-- Fully state-owned company & Certified by ISO9001-2008;
-- The largest professional manufacturer and supplier of Educational Equipments in the west of China;
-- Holding 5 factories, 2 warehouses & 6 international departments;
-- Managed by a trustworthy and professional team with experience of 30 years; -- Own brands: "MIGHTY", "NITOYO", "PEXMART"; -- 5 years' cooperation experiences with Alibaba.
SCMC-Sichuan Machinery Import & Export Company, formerly known as China National Machinery Import and Export Corporation, Sichuan Branch, is a fully state-owned company under Sichuan Foreign Trade Group. With international trade right authorized by The Ministry of Commerce in 1980, SCMC was also appraised as the national large second level enterprise and the first foreign trade company who obtained the ISO9000 International Quality Certification in the west of China. After the strict managements and 30 years' hard work, SCMC has now become an export-oriented modern foreign trade enterprise with six holding/shareholding companies and five import and export departments.
SCMC products activity includes: Lab Equipment, Optical Equipment, Medical/ Chemical/ Physical/ Biological/ Geological Educational Equipment, Various Kinds of Transmission Parts and Mechanical Parts, Paint Tools, Auto Parts / Motorcycle Parts, Construction Hardware, Grinding Tools and Materials, Machine Tools, Instrument and Apparatus, as well as the import and export business permitted by state, Leasing of Real Estate, Joint Venture, Co-production, Three Forms of OEM and Compensation Trade" Business. SCMC has its own holding processing plant and two large warehouses, based on which all kinds of transmission parts (including drawings and samples), spare parts, hand tools and other marketable products can be made according to the requirements of different customers.
SCMC accumulated many years of experience in import and export trade, gathered all kinds of professionals, persisted in the spirit of "Pioneering, Innovative, Stronger and Bigger ", adhere to the General Guideline of "Being Centered with Economic Benefits, Realized the Synchronized Growth of Exporting Scale and Benefit; Based on the Integration of Resources, Leaded by Business Development, to Improve Commodity, Capital and Talents Managing; Taking the system Construction as Safeguard, the Enterprise Culture as a Link, to Create First-class Foreign Trade Marketing Team". With excellent reputation, we will provide customers with quality products and provide first-class services to make our turnover increasing year by year. We are also expanding new products to increase profit margin and promote the brand development strategy at the same time. Till now, we have created three brands called "MIGHTY" "NITOYO" "PEXMART". Our brands have obtained wide acceptance and enjoyed good reputation, even become foreign customer's designated trademarks. These influences and sales channels have greatly enhanced the core competitiveness of enterprises.
SCMC adheres to the principle "Quality first, Honoring Contract and Credibility, to Provide Customers with Satisfactory Products and Services". We warmly welcome friends at home and abroad to establish long-term trade relations of cooperation with us.