Ads by Google
1.Clutch bearing AS series are sprag type freewheel,supported by bearing,good mobility and lower noise than As roller type freewheel.
2.Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation.
3.A typical arrangement is to install this type alongside a series 62 bearing, within the same location tolerance, as shown on the following page.
4.The outer race has a positive N6 tolerance, to give a press fit in a H6 housing. The inner race can be pressed on a shaft to K6 tolerance.
Type | Size | spped |
| Weight | Resistance | |||||
torque | ||||||||||
| TKN1) |
| Namax3 | Dr6 | L | e | f |
| TR | |
dH7 | Nm | nimax2) | min-1 |
|
|
|
|
|
| |
|
| min-1 |
|
|
|
|
|
|
| |
WAS(NSS) | 6 | 1.7 | 5000 | 7500 | 19 | 6 | 0.6 | 0.3 | 0.01 | 0.18 |
WAS(NSS) | 8 | 3.0 | 4300 | 6500 | 24 | 8 | 0.6 | 0.6 | 0.02 | 0.34 |
WAS(NSS) | 10 | 5.4 | 3500 | 5200 | 30 | 9 | 0.6 | 0.6 | 0.03 | 0.36 |
WAS(NSS) | 12 | 10 | 3200 | 4800 | 32 | 10 | 0.6 | 0.6 | 0.04 | 0.48 |
WAS(NSS) | 15 |
| 2800 | 4300 | 35 | 11 | 0.6 | 0.8 | 0.05 | 0.70 |
WAS(NSS) | 20 | 32 | 2200 | 3300 | 47 | 14 | 0.8 | 0.8 | 0.12 | 1.4 |
WAS(NSS) | 25 | 45 | 1900 | 2900 | 52 | 15 | 0.8 | 1 | 0.14 | 2.4 |
WAS(NSS) | 30 | 72 | 1600 | 2400 | 62 | 16 | 0.8 | 1 | 0.22 | 7.8 |
WAS(NSS) | 35 | 114 | 1300 | 2000 | 72 | 17 | 0.8 | 1 | 0.31 | 9 |
WAS(NSS) | 40 | 148 | 1200 | 1800 | 80 | 18 | 1.2 | 1 | 0.39 | 10 |
WAS(NSS) | 45 | 174 | 1000 | 1600 | 85 | 19 | 1.2 | 1 | 0.44 | 11 |
WAS(NSS) | 50 | 184 | 950 | 1500 | 90 | 20 | 1.2 | 1 | 0.49 | 13 |
WAS(NSS) | 55 | 246 | 800 | 1300 | 100 | 21 | 1.2 | 1 | 0.66 | 14 |
WAS(NSS) | 60 | 406 | 700 | 1100 | 110 | 22 | 1.2 | 1.5 | 0.81 | 26 |
WAS(NSS) | 80 | 850 | 600 | 900 | 140 | 26 | 1.2 | 1.5 | 1.41 | 58 |
clutch bearing